Filter the list by product size.
d (mm)
| d (mm) |
d1 (mm) |
D1. (mm) |
A (mm) |
B (mm) |
C (mm) |
e (mm) |
f (mm) |
MJ |
H (mm) |
H1 (mm) |
H2 (mm) |
L (mm) |
L1 (mm) |
w (mm) |
w1 (mm) |
w2 (mm) |
p1 (mm) |
p2 (mm) |
MK |
n (mm) |
Strok |
Product Code |
Price |
Stock |
3D |
Add to Cart |
|
8
|
7
|
4.5
|
11
|
20
|
8
|
10
|
7
|
M4
|
22
|
12.5
|
5
|
32
|
20
|
33
|
30
|
19
|
24
|
20
|
M3
|
3
|
10
|
G13308 |
|
|
|
|
|
10
|
7
|
5.5
|
15
|
25
|
10
|
12.5
|
9
|
M5
|
27
|
15.5
|
5
|
45
|
25
|
45
|
40
|
25
|
32
|
30
|
M4
|
4
|
18
|
G13310 |
|
|
|
|
|
12
|
10
|
7
|
17
|
25
|
12
|
15
|
11
|
M6
|
32
|
18
|
7
|
50
|
30
|
57
|
51
|
31
|
39
|
35
|
M6
|
6
|
20
|
G13312 |
|
|
|
|
|
16
|
12
|
9
|
22
|
30
|
16
|
15
|
14.5
|
M8
|
36
|
20
|
8
|
65
|
40
|
65
|
58
|
38
|
46
|
40
|
M6
|
6
|
25
|
G13316 |
|
|
|
|
|
20
|
14
|
11
|
26
|
40
|
20
|
16
|
18
|
M10
|
42
|
23
|
11
|
80
|
50
|
80
|
72
|
44
|
56
|
55
|
M8
|
8
|
30
|
G13320 |
|
|
|
|
|
25
|
16
|
14
|
32
|
45
|
25
|
17
|
22.5
|
M12
|
50
|
28
|
15
|
90
|
55
|
93
|
85
|
52
|
66
|
65
|
M10
|
10
|
35
|
G13325 |
|
|
|
|
|
30
|
18
|
14
|
38
|
50
|
30
|
17
|
27
|
M12
|
55
|
30
|
15
|
100
|
60
|
101
|
93
|
60
|
74
|
70
|
M10
|
10
|
40
|
G13330 |
|
|
|
|
|
35
|
20
|
14
|
45
|
60
|
35
|
18
|
32
|
M12
|
62
|
35
|
15
|
120
|
75
|
120
|
110
|
70
|
85
|
80
|
M12
|
10
|
45
|
G13335 |
|
|
|
|
|
40
|
25
|
18
|
55
|
70
|
40
|
19
|
36
|
M16
|
70
|
40
|
15
|
135
|
85
|
130
|
120
|
80
|
95
|
90
|
M12
|
10
|
50
|
G13340 |
|
|
|
|
|
45
|
30
|
18
|
60
|
80
|
45
|
24
|
40
|
M16
|
80
|
45
|
15
|
150
|
95
|
140
|
130
|
90
|
105
|
110
|
M12
|
10
|
55
|
G13345 |
|
|
|
|
It moves the Inclined / Angle Pin Systems in the desired angle. It provides important contribution to production period. The product parting from moulds with this unit is more economical compared with similar systems.
- The heat resistance of unit in mould is 300°c (with self lubricating bearing system), unit can lubricate itself.
- Operating angle of ejector pin can be inclined up to 10° - 20° - 30°C.
- It can be fastened to ejector plates via dowel pins and screws during mounting.
The position of the centre block can be adjusted according to the length of pin specified. Please make this adjustment when centre block and pin are attached and removed easily. For the precise bottom support of unit, G147 product can be used. The angle of ejector pin should be determined according to the angle of the product in mould.
